FIBERTHREE
F3 PA Pure Lite filament spool, side view
01 / 03Side view
PA12 blend unfilled Ø 1.75 mm

F3 PA Pure Lite

Unfilled PA12-based polyamide with very high impact strength, very low water absorption and a very smooth surface, in off-white.

COLOUR · OFF-WHITE
  • 01High-performance polyamide based on PA12, modified
  • 02Unfilled, no fibres
  • 03High strength with high impact strength
  • 04Very low water absorption, low warping
  • 05Excellent adhesion to the print bed
  • 06Very smooth surfaces (off-white)
01Properties

Measured on the printed part

Values according to the technical data sheet, measured on printed test specimens, just as you will use the material. “–” means: not stated in the data sheet.
PropertyTest directionUnitValue
MECHANICAL
Density–g/cm³1.14
Tensile modulusx-y 0°MPa3,300
Tensile strengthx-y 0°MPa80
Tensile strengthx-y ±45°MPa60
Tensile strengthx-y 90°MPa35
Impact strength (179eU)–kJ/m²135
Notched impact strength (179eB)–kJ/m²4.5
THERMAL
Glass transition temperature–°C88
Heat deflection temperature (HDT A, 1.8 MPa)–°C90
Continuous service temperature (IEC 60216)–°C120
ELECTRICAL & OTHER
Water absorption (24 h)–%< 0.3
Volume resistivity–Ω·m> 10¹²
Compared with F3 PA-CF Lite WITHOUT CARBON FIBRE · PRINTED TEST SPECIMENS
TENSILE MODULUS · MPA
PA PURE LITE
3,300 MPa
PA-CF LITE
10,000 MPa
IMPACT STRENGTH · KJ/M²
PA PURE LITE
135 kJ/m²
PA-CF LITE
35 kJ/m²
Without fibres: around a third of the stiffness of F3 PA-CF Lite, but almost four times the impact strength.
02Material & processing

Impact-resistant and smooth

Material properties

Technical polyamide filament, modified for 3D printing. The material shows high strength with low tendency to warp, low water absorption, very high impact strength and layer adhesion. Thanks to its good heat and media resistance, it is suitable for high-strength parts.

It differs from F3 PA-CF Lite in having no fibres. This makes it suitable as a reference material for the influence of fibres, for multi-material parts and as an alternative when a smooth surface is required or fibres get in the way.

The heat required in the hotend is considerably higher than for F3 PA Pure Pro.

Processing notes
  1. 01Store and print the filament dry.
  2. 02Print slowly: 25 mm/s, high heat demand for melting.
  3. 03Printable with any nozzle. No abrasion-resistant nozzle is needed.
Print parameters
NOZZLE270–300 °C
PRINT BEDmax. 90 °C
MINIMUM NOZZLE DIAMETER0.4 mm
SPEED25 mm/s
03Printers & downloads

Tested and documented

Tested on
  • 01Raise3D Pro2 (test specimens according to data sheet)
  • 02Prusa MK3S+ / MK4S / Core One / Core One L / XL / HT90
  • 03Bambu Lab A1 / P1S / X1C / H2D
Downloads
DocumentVersionLanguage
Technical data sheetDE v8/2024 · EN v12/2024DE · EN
Safety data sheetv04DE · EN
Slicer profilesOn requestENQUIRE
04Where to buy

Available from

This dealer stocks F3 PA Pure Lite. You will find all dealers and countries on the distributors page.
UNITED KINGDOM3DGBIRETo the product in the shop