FIBERTHREE
F3 PA-CF Lite filament spool, side view
01 / 04Side view
PA12 blend 15 % Carbonfaser Ø 1.75 mm

F3 PA-CF Lite

Carbon-fibre-reinforced PA12-based polyamide with very low water absorption, very low warping and good wear resistance. For high-strength lightweight parts.

COLOUR · BLACK
  • 01High-performance polyamide based on PA12, modified
  • 0215 wt% carbon fibre
  • 03High strength, very low water absorption
  • 04Very low warping, good wear resistance
  • 05Excellent adhesion to the print bed
  • 06Matt black surface
01Properties

Measured on the printed part

Values according to the technical data sheet, measured on printed test specimens, just as you will use the material. “–” means: not stated in the data sheet.
PropertyTest directionUnitValue
MECHANICAL
Density–g/cm³1.24
Tensile modulusx-y 0°MPa10,000
Tensile strengthx-y 0°MPa90
Tensile strengthx-y ±45°MPa65
Tensile strengthx-y 90°MPa50
Flexural modulusx-y ±45°GPa4.12
Impact strength (179eU)–kJ/m²35
Notched impact strength (179eB)–kJ/m²4.03
THERMAL
Glass transition temperature–°C87
Heat deflection temperature (HDT A, 1.8 MPa)–°C90
Continuous service temperature (IEC 60216)–°C120
ELECTRICAL & OTHER
Water absorption (24 h)–%< 0.3
Volume resistivity–Ω·m> 10¹⁰
Compared with F3 PA-CF Pro PA12 INSTEAD OF PA6 · PRINTED TEST SPECIMENS
TENSILE MODULUS · MPA
PA-CF LITE
10,000 MPa
PA-CF PRO
10,500 MPa
TENSILE STRENGTH X-Y 0° · MPA
PA-CF LITE
90 MPa
PA-CF PRO
110 MPa
Slightly lower strength than F3 PA-CF Pro, but very low water absorption and less sensitive to moisture during printing.
02Material & processing

Light, stiff, insensitive to moisture

Material properties

Technical polyamide filament, modified for 3D printing, with an additional carbon fibre filler. The carbon fibres minimise shrinkage, so warping is largely reduced.

The material shows very high strength while retaining impact strength, very low tendency to warp and very good layer adhesion. Thanks to its good heat and media resistance, it is suitable for high-strength or lightweight parts. Very attractive surface with a matt sheen.

Compared with F3 PA-CF Pro: less sensitive to moisture during printing, but needs considerably more heat to melt.

Processing notes
  1. 01Always use a wear-resistant nozzle.
  2. 02Store and print the filament dry.
  3. 03Very stiff filament: it can break at tight bend radii in the feed.
Print parameters
NOZZLE290–310 °C
PRINT BEDmax. 90 °C
MINIMUM NOZZLE DIAMETER0.4 mm
SPEED25 mm/s
03Printers & downloads

Tested and documented

Tested on
  • 01Raise3D Pro2 (test specimens according to data sheet)
  • 02Prusa MK3S+ / MK4S / Core One / Core One L / XL / HT90
  • 03Bambu Lab A1 / P1S / X1C / H2D
Downloads
DocumentVersionLanguage
Technical data sheetDE v8/2024 · EN v12/2024DE · EN
Safety data sheetv04DE · EN
Slicer profilesOn requestENQUIRE
04Where to buy

Available from

This dealer stocks F3 PA-CF Lite. You will find all dealers and countries on the distributors page.
UNITED KINGDOM3DGBIRETo the product in the shop