FIBERTHREE
F3 PA-GF Pro filament spool (black), side view
01 / 05Side view
PA6 blend 15 % Glasfaser Ø 1.75 mm

F3 PA-GF Pro

Technical polyamide filament with 15 % glass fibre: high strength, low warping, non-conductive. In off-white and black.

COLOUR · Black
  • 01High-performance polyamide based on PA6, modified
  • 0215 wt% glass fibre
  • 03High strength, moderate water absorption
  • 04Low warping
  • 05Excellent adhesion to the print bed
  • 06Matt surface in off-white or black
01Properties

Measured on the printed part

Values according to the technical data sheet, measured on printed test specimens, just as you will use the material. “–” means: not stated in the data sheet.
PropertyTest directionUnitValue
MECHANICAL
Density–g/cm³1.27
Tensile modulusx-y 0°MPa5,560
Tensile modulusx-y 90°MPa3,500
Tensile strengthx-y 0°MPa90
Tensile strengthx-y ±45°MPa80
Tensile strengthx-y 90°MPa70
Stress at breakx-y 0°MPa89.68
Elongation at breakx-y 0°%1.98
Flexural modulusx-y ±45°GPa3.08
Notched impact strength (179eB)–kJ/m²4.19
THERMAL
Glass transition temperature–°C65
Heat deflection temperature (HDT A, 1.8 MPa)–°C90
Continuous service temperature (IEC 60216)–°C120
ELECTRICAL & OTHER
Water absorption (24 h)–%0.3
Volume resistivity–Ω·m> 10¹²
Compared with F3 PA-GF30 Pro 15 % INSTEAD OF 30 % GLASS FIBRE · PRINTED TEST SPECIMENS
TENSILE MODULUS · MPA
PA-GF PRO
5,560 MPa
PA-GF30 PRO
8,070 MPa
TENSILE STRENGTH X-Y 0° · MPA
PA-GF PRO
90 MPa
PA-GF30 PRO
106 MPa
Half the glass fibre content, lower stiffness. If you need maximum stiffness, choose F3 PA-GF30 Pro.
02Material & processing

Strong, low-warp, non-conductive

Material properties

Technical polyamide filament, modified for 3D printing, with an additional glass fibre filler. The glass fibres minimise shrinkage, so warping is largely reduced.

The material shows enormous strength while retaining impact strength, very low tendency to warp and very good layer adhesion. Thanks to its good heat and media resistance, it is suitable for high-strength, lightweight parts. Resistant to oil, grease, fuels and many chemicals. Rough surface with a matt sheen.

Compared with F3 PA-CF Pro: the fibres are non-conductive and strength is slightly lower.

Processing notes
  1. 01Always use a wear-resistant nozzle.
  2. 02Store and print the filament dry.
  3. 03Very stiff filament: it can break at tight bend radii in the feed.
Print parameters
NOZZLE270–285 °C
PRINT BEDmax. 80 °C
MINIMUM NOZZLE DIAMETER0.4 mm
SPEED50 mm/s
03Printers & downloads

Tested and documented

Tested on
  • 01Prusa MK3S+ (test specimens according to data sheet)
  • 02Prusa MK3S+ / MK4S / Core One / Core One L / XL / HT90
  • 03Bambu Lab A1 / P1S / X1C / H2D
Downloads
DocumentVersionLanguage
Technical data sheetDE v8/2024 · EN v12/2024DE · EN
Safety data sheetv04 · black: separate SDS v04DE · EN
Slicer profilesOn requestENQUIRE
04Where to buy

Available from

These dealers stock F3 PA-GF Pro. You will find all dealers and countries on the distributors page.
CZECH REPUBLICPrusa ResearchTo the product in the shop
UNITED KINGDOM3DGBIRETo the product in the shop